Home - Bituminous - Modified Bituminous Membranes - APP Modified - Roofseal P & G

ROOFSEAL - Polymer Modified Bitumen Membrane with Nonwoven Polyester or Glass Reinforcement

DESCRIPTION

BITUMAT ROOFSEAL is a pre-fabricated polymer modified bitumen membrane designed for economy and easy applications.

BITUMAT ROOFSEAL “P” is re-inforced with a non-woven polyester fabric, whereas BITUMAT ROOFSEAL “G” is reinforced with a glasfiber mat. The re-inforcement is impregnated and coated on both sides with polymer modified bitumen.

Roofseal P & G
USER

BITUMAT ROOFSEAL membrane is ideal for a wide range of waterproofing applications including roofs, basements, tunnels, car parks and reservoirs.

OUTSTANDING FEATURES

Total impermeability Good bondability & seam integrity Stability at high temperature Good flexibility Compatible with all normal roofing and building components

GENERAL DATA

Nominal Roll Length : 10 Mtrs. Nominal Roll Width : 1 Mtr. Nominal Thickness : 3,4,5, MM Nominal Weight : 4mm / 47 Kgs per Roll Re-inforcement : Non-woven polyester / Glasfibre mat

PACKAGING

3mm - 28 rolls / pallet 4mm - 23 rolls / pallet

FINISHES

BITUMAT ROOFSEAL is available in two basic finishes:

1. Black smooth finish with polyethylene surfaces for covered applications.

2. Granule surfacing for exposed applications.

QUALITY CONTROL

In addition to stringent regular tests by BITUMAT laboratory, our products are tested periodically by Independent laboratories.

APPLICATION

BITUMAT ROOFSEAL is installed by torch welding method, loose-laid or fully bonded to substrate. When loose-laid, only laps are bonded together.

Peripheries and protrusions are sealed according to specifications.

INSTALLATION TOOLS REQUIRED

Gas torch, Knife, Trowel, Measuring tape, Marking string, Gloves.

COVERAGE RATE (Approx.)

(Rate may vary as per site requirement)

Flat areas : 1.15 M2 /M2 per layer with 10 cms. side laps and 15 cms. end laps. Base flashing : 100x35 cms. with 15 cm. end laps, 0.40 M2 / Linear Mtr. Average wastage : 3 - 5 %

TORCHING GUIDELINES

The underside of the membrane should be torched just enough to superficially melt the bitumen. Excessive heating may damage the re-inforcement.

Overlaps should be re-heated from the top and resealed with a trowel to ensure seam integrity.

For details of installation methods and flashing requirements, consult the relevant BITUMAT Systems Design and Installation Manual.

المصادر التقنية

تأسست شركة بيتومات في عام 1984 ، ولكن جذورها تعود إلى عام 1975 عندما شارك المؤسسون في صناعة العزل المائي للأسقف بصفتهم تجاراًومركبين في المملكة العربية السعودية لشركة تصنيع رئيسية من الولايات المتحدة الأمريكية.

B.I.R.A
مشاهدة الكل

أكاديمية الأسقف والعزل المائي الوحيدة في الشرق الأوسط! حضر الأكاديمية آلاف من الممثلين من مختلف أنحاء العالم وتخرجوا بمرتبة الشرف. يمكنك أيضاً أن تكون واحداً منهم.......

شهادات
مشاهدة الكل

تؤمن بيتومات بالجودة والتي تتميز بكونها الأفضل ، بل الدائمة أيضاً.

التنزيلات
مشاهدة الكل

تم توفير قاعدة بيانات لتحميلهاو مساعدتك للوصول على المعلومات الصحيحة عندما تكون في أمس الحاجة إليها.

شاهد الفيديو
مشاهدة الكل

فيديوهات متنوعة لشرح جوانب مختلفة. مكتبة الفيديو الخاصة بنا قيد الإنشاء

سياسة الخصوصية - الشروط والأحكام

© 2020 www.bitumat.com-ACT, All rights reserved. AI